Air King AKLC703 Troubleshooting Guide download pdf (Page 3)

1b. Internal Wire Compartment: Remove the screw holding the blower assembly in place. Lift

up on the assembly and tilt it at a 45° angle to remove from the housing (Figure 7). Remove

the wire compartment cover screw and place the cover in a secure place (Figure 8).

NOTE: If the fan motor plug is

connected to the fan housing

receptacle, unplug so the

blower assembly can be

completely removed.

2a. Wiring Fan/Light Independently: Run wiring from an approved wall switch carrying the

appropriate rating. One neutral (white), one ground (green or bare copper), and two hot

(black lead connected to the switch). Secure the electrical wires to the housing with an

approved electrical connector. Make sure you leave enough wiring in the box to make the

connection to the fan’s receptacle.

2b. From where you have access to inside the fan’s junction box, connect the one white wire

from the house to both the white wire from the fan’s light receptacle and the white wire

from the fan’s exhaust receptacle. Connect the ﬁrst black wire from the wall switch to the

red wire from the fan’s light receptacle. Connect the second black wire from the switch to

the fan’s exhaust receptacle. Connect the ground wire from the house to the green wire

from the fan’s grounding screw (Figure 9). Use approved methods for all connections.

3a. Wiring Fan/Light together: Run wiring from an approved wall switch carrying the

appropriate rating. One neutral (white), one ground (green or bare copper), and one hot

(black lead connected to the switch). Secure the electrical wires to the housing w ith an

approved electrical connector. Make sure you leave enough wiring in the box to make the

connection to the fan’s receptacle.

3b. From where you have access to inside the fan’s junction box, connect the one white wire

from the house to both the white wire from the fan’s light receptacle and the white wire

from the fan’s exhaust receptacle. Connect the black wire from the wall switch to both

the red wire from the fan’s light receptacle and the black wire from the fan’s exhaust

www.airkinglimited.com

210572200 Rev. B 1-13 3 of 12

receptacle. Connect the ground wire from the house to the green wire from the fan’s

grounding screw (Figure 10). Use approved methods for all connections.

4. Carefully tuck wire back inside wire compartment and replace wire compartment cover

securing with the screw that was removed earlier.

SECTION 6

Completing the Installation

1. If the fan’s blower assembly was removed during the wiring process, reinstall the blower

by reversing the directions in Step 1b in Section 5 Wiring.

2. Insert the fan’s plug into the receptacle (Figure 7).

3. Remove glass light lens from grill by unscrewing knob at the top of lens (Figure 11).

4. Plug cord from lamp holders into the appropriate receptacle (Figure 12).

5. Line up slots in the grill with lances on inside of housing. Insert included #8 screws

through grill slots and into housing lances. Tighten both screws until the grill ﬁts snugly

to the ceiling. DO NOT OVER TIGHTEN (Figure 13).

Figure 6

Screw

Wire

Compartment

Cover

Figure 7

Screw

Wire

Compartment

Cover

Plug

Screw

Figure 9

Supply

from

house

Neutral (White)

Ground (Green or Bare)

Hot

(Black)

Hot (Red)

Figure 10

Supply

from

house

Neutral (White)

Ground (Green or Bare)

Hot (Black)

Hot (Red)

Figure 11

Glass Lens

Knob

Figure 13

Grill

Lances

#8 Screws

Cord

Figure 12

Lamp

Holders

Figure 8

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

Air King AKLC703 Troubleshooting Guide Page 3

Comments to this Manuals

Related products and manuals for Unknown Air King AKLC703