Air-king Fan User Manual download pdf

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

DESCRIPTION

The AirKing 18" (45.7 cm) I-Beam Mount Fan features Pull Cord operation

and a 3-paddle Fan Blade. This Fan has a permanently lubricated motor

with a 9 ft (2.74 m) 18/3 cord set and are constructed of sturdy, powder

coated steel.

SPECIFICATIONS

Motor ....................................... 120 V, 50/60 Hz

Blade diameter ....................... 18" (45.7 cm) Model 9618

Speeds ....................................3

Control .................................... Pull Cord

Air flow distribution ................. 360°

Approvals ................................ UL Listed. Close mesh Fan guard

meets OSHA requirements.

HIGH VELOCITY

I-BEAM MOUNT FAN

18" (45.7 cm) MODEL 9618

OPERATING INSTRUCTIONS & PARTS MANUAL

GENERAL SAFETY INFORMATION

1. Make certain that the power source conforms to the electrical require-

ments of the Fan.

2. The power cord is equipped with a three-prong grounded plug that must

be inserted into a matching receptacle. Under no circumstances must the

grounding prong be cut off the plug. Where a two-prong wall receptacle

is encountered, it must be replaced with a properly grounded three-prong

receptacle installed in accordance with the National Electrical Code

(NEC) and all applicable local codes and ordinances. This work must be

done only by a qualified electrician, using copper wire only.

WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS

NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE THE

RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS ARE NOT

PERMITTED IN CANADA.

3. Where possible, avoid the use of extension cords. If they must be

used, minimize the risk of overheating by ensuring that they are UL

listed and of the proper gage and length. Never use a single extension

cord to operate more than one fan.

4. Do not insert fingers or foreign objects into the fan. Do not block or

tamper with the fan in any manner while it is in operation. Do not touch

the fan while in operation or just after it has been turned off, as some

parts may be hot enough to cause injury.

5. Unplug power cord before installing or servicing the fan.

WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE

SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR

SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD.

6. This fan is intended for general use ONLY. It must NOT be used in

potentially dangerous locations such as flammable, explosive, chemi-

cal-laden or wet atmospheres.

New 6/01 1 5084036

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE.

CAUTION: BECAUSE OF SIZE AND WEIGHT OF THIS FAN, MAKE

SURE ALL PARTS ARE COMPLETELY ASSEMBLED ACCORDING TO

INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN FAN COM-

ING APART DURING OPERATION AND/OR PERSONAL INJURY.

7. Be sure Fan is mounted to a stable surface when operating.

8. DO NOT mount Fan near windows or bay doors. Rain may create an

electrical hazard.

9. Completely reassemble Fan, according to instructions before recon-

necting to power supply.

MODEL

9618

SPEED

HIGH MED LOW

CFM 5350 4180 3010

/s 2.52 1.97 1.42

RPM 1600 1275 950

Amps 1.65 1.27 .95

Watts 194 148 110

dB A 67 58 49

I-BEAM MOUNT INSTALLATION

1. Locate the L-shaped pipe to the desired location on the I-Beam

flange. Install the 5/16 x 2" U-Bolt over the pipe and through the

clamping plate holes. The flat part of the clamping plates fits on the

I-Beam flange and the end with the slight bend goes against the

pipe. Install flat washers, lock washers and nuts. Finger tighten the

nuts on the U-Bolt. (

Figure 1

)

2. Slide the clamping plates onto I-Beam flange until U-Bolts contact flange.

3. Adjust L-shaped pipe so forward clamp plate is as close to the label at

the bend as possible.

4. Tighten nuts on bolt so pipe does not move.

5. Screw on the adapter mount as far as it will go onto the L-shaped pipe.

Tighten set screw in pipe coupling with Allen Key provided.

6. Tighten Bolt on Fan Mount after positioning fan to desired position.

5/16 Nut

5/16 Lock

Washer

5/16 Flat

Washer

1/4" Set Screw

Figure 1

Tighten

Bolt

Tighten Clamp

Plate Here

1 2

Summary of Contents

Page 1 - I-BEAM MOUNT FAN

READ AND SAVE THESE INSTRUCTIONSREAD CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.PROTECT YOURSELF AND

Page 2 - MODEL 9618

MODEL 9618New 6/01 2 5084036CAUTION: THE SECONDARY SUPPORT CABLE PROVIDEDSHOULD BE USED ANYTIME THE CIRCULATOR IS MOUNTEDOVERHEAD FOR ADDITIONAL SAFET

Comments to this Manuals

No comments

Air-king Fan User Manual

Browse online or download User Manual for Faxes Air-king Fan. Air King Fan User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Faxes Air-king Fan