Air King 6000 Operations Instructions download pdf (Page 11)

1. MAIN ON/OFF POWER BUTTON FOR THE HUMIDIFIER. –

Use this button only when turning ON or OFF the humidifier.

2. REDUCE RELATIVE HUMIDITY SET POINT BUTTON. – Use

this button only when reducing the relative humidity set point.

3. INCREASE RELATIVE HUMIDITY SET POINT BUTTON. – Use

this button only when increasing the relative humidity set point.

4. DIGITAL DISPLAY. – Displays (fig 32) a) User Set Point. b) Set

Point Number Indication. c) Humidifier Operating Indication.

d) Actual relative humidity being sensed. e) Incremental bar

indicating relative humidity status as it relates to the set point.

5. MAIN POWER GREEN LED. – Indicates that the main power

to the humidifier is ON.

When power is first turned on to the humidifier the digital

humidistat will display the default set point, which is 35%. You

may change this setting by using the Increase or Decrease button

on the control. If for some reason the power is lost to the

humidifier (power outage or unit becomes unplugged) there is a

delay (30 sec to 1 min) before the control loses it’s set point,

however if power is lost for any length of time the control will

revert to the default settings. If you notice that the control is

consistently resetting to the set point this is an indication that, a)

You have not wired (or plugged in the transformer) the

transformer to a CONSTANT 120 volt supply (one which cannot

be shut off via a switch) or b) The power connections (Two Black

Wires) to the humidifier are loose.

What is displayed will depend on what the set point is, what the

relative humidity being sensed is, and if the set point is being

changed.

DIGITAL DISPLAY WHEN CHANGING THE HUMIDITY LEVEL (FIG 33)

When you start to change the set point (raising or lowering) the

display will change, showing two numbers and a pointing finger

(the water droplets may be displayed as well depending on what

the relative humidity status was before you started changing the

set point). The number displayed beside the pointing finger is the

set point and is the number you are changing – The larger

number on the left of the display is the actual relative humidity

being sensed.

DIGITAL DISPLAY WHEN HUMIDIFIER HAS REACHED THE SET

POINT (FIG 34)

When the relative humidity being sensed raises above the set

point the humidifier does not need to run and the control display

will be similar to above – It will show two numbers and a pointing

finger. The number displayed beside the pointing finger is the set

point – The larger number on the left of the display is the actual

relative humidity being sensed.

DIGITAL DISPLAY WHEN HUMIDIFIER IS HUMIDIFYING. (FIG 35)

When the humidifier is adding moisture to air the display will

change – In the top right of the display will be a number, this is

the set point. - In the mid lower section of the display will be

water droplets, this is indicating that the humidifier is adding

moisture. - The remaining portion of the display will be taken up

by a slanted incremental bar, This bar represents the percentage

of the set point achieved.

SLANTED INCREMENTAL BAR.

When humidifying the control will display the set point and a bar

representing the percentage of set point achieved – each bar

represent approximately 10% of the set point. Below are a few

examples of humidifying displays showing a set point, an

incremental bar, and what relative humidity they represent.

1. Set point 40% - 50% of bars showing - relative humidity 20%

2. Set point 45% - 80% of bars showing – relative humidity 36%

3. Set point 50% - 50% of bars showing – relative humidity 25%

CONTROLLING THE HUMIDITY LEVEL

AND HUMIDIFIER OPERATION

HUMIDIFIER START UP.

When you first plug in the 24 Volt transformer and turn on your

humidifier you may hear a click. This is the power getting to the

control’s relay – As well if you adjust the digital humidistat UP or

DOWN and past the sensed humidity level you may hear the

control’s relay clicking. This is normal as the humidistat is just an

ON/OFF switch, every time the digital humidistat is turned

DOWN the power is cut to the HUMIDISENSE control.

When starting up the humidifier for operation:

1. Make sure the transformer is plugged in and the water supply

is turned on.

2. Make sure main power to the humidifier is turned ON.

3. Turn the humidistat up high, so it is calling for humidity.

4. Turn your furnace thermostat UP so the furnace cycles ON.

5. Once the HUMIDISENSE control senses heat the humidifier will

turn ON. You will know because the green “HUMIDISENSE”

LED (fig. 23) on the front of the humidifier will turn ON.

6. After a few moments you should hear water trickling through

the drain.

7. After your furnace has complete the heating cycle and shut off

Model 6000 Flow Through Humidifier

Figure 31

Slanted Incremental Bar

Figure 32

Figure 33

Figure 34

Figure 35

1 2 ... 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Air King 6000 Operations Instructions Page 11

Comments to this Manuals

Related products and manuals for Dehumidifiers Air King 6000