Air King Advantage Professional Series Troubleshooting Guide download pdf (Page 5)

www.airkinglimited.com

A111597016 Rev. F 4-12 5 of 16

SECTION 8

Installing the Blower

Refer to the instructions inc

luded with the blower for installation.

SECTION 9

Installing the Optional Sofﬁts

Refer to the instructions inc

luded with the speciﬁc sofﬁt(s) you have chosen for installation.

SECTION 10

Finishing the Installation

Install the proper lighting for your speciﬁc unit:

Halogen Lamps:

Use PAR16 medium base 45W maximum lamps (available separately).

Install by inserting lamp into socket and turning clockwise until lamp is ﬁrmly seated. DO NOT

over tighten.

Heat Lamps:

Use type R40, medium base IR 250W max lamps only (available

separately). Install by inserting lamp into socket and turning clockwise until lamp is

ﬁrmly seated. DO NOT over tighten.

2. Install the grease ﬁlters by inserting the bottom of the ﬁlter into the bottom channel of the

hood compressing the spring, then slide the top of the ﬁlter into the top channel of the

hood (Figure 18).

SECTION 11

Operation

Controls

Your Range Hood is equipped with two rotary switches with one controlling the lighting and

the other controlling the exhaust fan blower. The light switch has three positions, High, Low,

and OFF. The fan switch has four positions, Off, High, Medium, and Low (Figure 19).

NOTE: On installation where a One (1) speed blower is utilized, all blower control speeds

operate at the same speed. On installation where a Two (2) speed blower is utilized, the

Medium and High speeds operate at the same speed.

Heat Lamp Controls: For models equipped with heat lamps, two On/Off rocker switch are

located on the front underside of the hood for independent control of the heat lamps (Figure 19).

Thermostat

Your hood is equipped with a thermostat that will automatically turn the hood on when the

temperature exceeds a set point. Once the temperature drops, the thermostat will turn the

hood off.

CAUTION: THE HOOD SHOULD ALWAYS BE TURNED ON OR OFF USING THE

CONTROL PANEL ANYTIME THE COOKING SURFACE IS BEING USED. DO NOT RELY ON THE

THERMOSTAT AS THE SOLE MEANS OF TURNING THE HOOD ON OR OFF!

Figure 18

Top

Channel

Bottom

Channel

SECTION 12

Maintenance

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

SERVICING THE UNIT.

Grease Filters

Included with your range hood are grease ﬁlters along with a grease trough that should be

washed at least once a month. The grease ﬁlters are dishwasher safe and should be washed

in a mild soap or detergent. Reverse the instruction in SECTION 10 Finishing the Installation,

to remove the grease ﬁlters and trough. If the grease ﬁlters become damaged, replace with Air

King Models:

AP1030: Model GF1030 Grease Filters

AP1036:

Model GF1036 Grease Filters

AP1830:

Model GF1830 Grease Filters

AP1836:

Model GF1836 Grease Filters

CAUTION: ALLOW BULB TO COOL BEFORE REPLACING.

Changing the Lamps

Unscrew the lamp by turning in a counter-clockwise direction and remove from the socket.

Replace with a PAR16 medium base 45W maximum Halogen lamp. Installation is the reverse

of removal.

Cleaning

CAUTION: DO NOT USE GASOLINE, BENZINE, THINNER, HARSH CLEANSERS, ETC.,

AS THEY MAY DAMAGE THE RANGE HOOD.

Clean your range hood with a mild detergent,

such as dishwashing liquid, and dry with a

soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS. Completely dry

before restoring power. NEVER IMMERSE ELECTRICAL PARTS IN WATER.

The blo

wer assembly can be vacuumed when build up (dirt, lint, etc.) accumulates over

time. The blower is permanently lubricated and does not require oiling.

Light Switch

Blower Switch

Figure 19

Heat Lamp Switch

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Air King Advantage Professional Series Troubleshooting Guide Page 5

Comments to this Manuals

Related products and manuals for Cooker hoods Air King Advantage Professional Series